Design is for 1 Storey single family residence 2590 Sq. Ft.
Please read solution specification below and then look at solution components (links to products) at the bottom to get a complete view of your solution. Please send us email with questions/comments you might have.
To place the order, Keep this page open and click on each item and add it to the shopping cart on the other window that pop's up. Make the quantity and color choices recommended. Once an item is added come back to this page and click on next item. Keep adding items to cart and go to checkout and fillout first page to get a price quote including shipping charges.
Solution Specification:
Four types of outlets for audio video data telephone (whole house described seperately)
VDT : Video, Data, Telephone, powered by composite cable
DT : Data + telephone powered by cat5e cables
HT : Home theater 5 pairs of binding post modules for audio input. Located behind entertainment/TV unit. (Other end terminates directly on to the speakers.
VC : video camera, run one RG6 and 1 cat5e to each of the interior/exterior camera location. Three technologies available, CCTV($), IP camera($$), IP camera with Power over ethernet($$$) wire for both.
CCTV uses 1 RG6 for video and cat5e for 12V DC
IP camera uses cat5e for signal and control and have a 110 V AC close by for power.
IP camera with power over ethernet handles signal/control and power all from one cat5e but is very expensive now.
When pre-wiring for video camera leave ample extra length on camera end and cover gang box with wallplate.
Home Orientation
For ease of communication I have considered
top of page to be North, Bottom is South, Right edge
of page is East and Left edge of page is West.
Bedroom #1
1 VDT on the west wall
1 Dt on the east wall
Whole house audio - zone 1
Study
1 VDT on west wall
1 DT on east wall
Covered Patio
Whole house audio - zone 2
1 DT on west wall
Family Room
1 VDT on west wall
1 DT on east wall
1 HT for 7.1 surround sound/home theater
(also the head-end for the audio zone zero)
Family Dining Room(FDR)
1 VDT on east wall
Whole house audio - zone 3
BreakFast Area
1 VDT on east wall
Whole house audio - zone 4
Kitchen
1 VDT on west kitchen wall under cabinet/on splash-board to allow tel, data and under cabinet TV.
1 DT on splash board of the kitchen Island/bar for laptop/kitchen phone
1 T Leviton out-of-sight jack for main home phone/answering machine.
Bedroom #2
1 VDT on west wall for computer
2 DT on north or east wall
Bedroom #3
1 VDT on west wall as directed in the floor plan
2 DT on east wall
Bedroom #4
1 VDT on east wall
2 DT on south wall
2 Car Garage
1 VDT on the west wall for the computer.
1 HT for 7.1 surround sound/home theater
Whole House Audio
A 4-zone A-bus whole house audio system with built in IR repeater system. Building blocks are:
4 zone distribution module installed at the wall where the main entertainment unit will reside (Family room)
Wiring is 1 cat5e from distribution module to each amplified keypad. Speaker wire 14/2 from keypad to the ceiling/wall speakers. Family room is already covered with the entertainment unit, you could go with 4 zones :Bedroom #1, Covered Patio, Family Room (zone 0), Breakfast.
4 zones audio will be economical for you.
Please not the A-bus single zone does not come with speakers You have to purchase the speakers separately.
Total outlets(wallplates) of each type
VDT=10
DT=11
HT=2
T=1
Audio Zone 4 recommended.
Total outlets by service type
Video= 10
Data =10 + 11 = 21
Telephone 10 + 11 + 1 = 22
Surround sound 7.1/Home Theater 2
Solution Components:
Structured Wiring Panel
These panels(cabinets) are designed to fit between studs (2x4inch wooden colums) and mount flush with the wall. Unit comes as a can and a cover. the can mounts flush with the finished wall. The cover rides
on the wall and screws into the can and will rise 1/4 inch from the wall.